⎝⎛多人牛牛⎞⎠

苏州萨瓦智能科技有限公司

Manufacturer of SAW intelligent lithium battery automated production equipment

13451760748 18912673551 SAVA Smart Service Hotline 13451760748 18912673551

萨瓦智能制造,提质增效

Study on the Automatic Production Line System of Lithium Battery

发布日期: 2019.12.28 Back to list source: SAVA Smart Release Date: 2019.12.28


与控制程序同等重要的是工业级人机交互平台的建立。 As important as the lithium battery automated production line and control program is the establishment of an industrial-grade human-computer interaction platform. The system requires that in the work, the operator can either monitor the equipment to run automatically as the supervisor, or operate the equipment as the commander to run according to his will. 这个目的,苏州萨瓦有专业级的人机交互界面与灵活的软件平台来实现。 In order to achieve the purpose of automated production line for lithium batteries , Suzhou Sawa has a professional-level human-computer interaction interface and a flexible software platform. In a good industrial-grade interactive platform, the resistive touch screen is waterproof and shockproof. The included programming software AD2P. 5 3 can realize the creation of various virtual elements such as buttons, charts, progress bars, marquees, date display, etc., and fully meet the needs of human-computer interaction in technical systems.

设计分析,输出部分硬件如下 : ( 1)中间继电器型号为: 解一c2直流线圈,即MY型、两对触点、内置动作显示灯、内置抑制浪涌二极管、线圈额定电压DC6 一 1 0V0 、额定功耗 DC O , W9 、触点额定电压为CA 2 20 V、5A、使用次数20万次以上。 The output components of this system are all inductive loads.Built-in surge suppression diodes can be used to prevent back-EMF from entering the programmable controller, disturbing the program or burning out the output port. According to the design and analysis of the lithium battery automated production line , the output hardware is as follows: (1) The model of the intermediate relay is: a c2 DC coil, that is, MY type, two pairs of contacts, built-in action indicator, built-in surge suppression diode, coil rated voltage DC6 to 10V0, rated power consumption DC O, W9, The rated voltage of the contact is CA 2 20 V, 5A, and the number of use is more than 200,000 times.

(2) DC solenoid valve model is SY 3 120-SLZ D-MS, DC coil, built-in action indicator, built-in surge suppression diode, rated power consumption DC 5. W4 6-3-1-1 4 selection of strong power components For thermal relays, the rated current of the motor is mainly considered. In special cases, such as when the equipment does not allow any power outage, the rated current of the thermal element of the selected thermal relay should be higher than the rated current of the motor for protection. The rated current of the motor.

According to the design analysis, the hardware of the high-voltage part of the main line of the lithium battery automated production line is as follows:

(1) DC power supply The model of the DC power supply is: S 8 2 K-10 0 2 4, 1 parameter: input voltage AC 10 0/2 0 0 V switching type; output voltage DC2 4 V; output current 4. 2A; capacity I OOW; with clutter filter.

(2) Programmable output terminal protection diode for fuse. Diode current can be selected as 1A; motor protection diode, diode current can be selected as 2 A

空气开关 ( 断路器 ) 型号 : S A3 B , S A32 B , 各 1 个 , 参数为 : 三相 / 单相 , 最大电流 2 0A , 三相空气开关带漏电保护,热继电器 3 个用于驱动转盘的大电机的额定电流为1A , , 热继电器的整定电流取0 . 9 一1 4A 的,5个用于驱动传送带的大电机的额定电流为 O . 7A , 可以打滑 , 因此 , 热继电器可以不要。 Air switch (circuit breaker) for lithium battery automated production line Model: S A3 B, S A32 B, 1 each, parameters are: three-phase / single-phase, maximum current 20 A, three-phase air switch with leakage protection, 3 thermal relays The rated current of the large motor used to drive the turntable is 1A, the setting current of the thermal relay is 0.9 to 14A, and the rated current of the five large motors used to drive the conveyor is O. 7A, which can slip, so, The thermal relay can be omitted.


【related suggestion】

support hotline

13451760748
七乐彩 新金沙线上娱乐 欢乐拼三张 必赢真人娱乐